How to wire a fluorescent light fixture to a switch

Free Delivery on Eligible Orders! Buy LED Lightbulbs at LightBulbs-Direct. Wide range of Electronic Components at Competitive Prices. Switches , LEDs, Wire and more.

After making every thing is secure, switch on the light. If the florescent light doe not light up, give the florescent tube and the starter a slight twist.

Wire connections may vary according the the manufacturer of the fluorescent light fixture. Refer to the installation instructions or the wiring diagram on the inside face of the cover plate for. James, please follow the links below so you will see how a light switch is wired to operate your light fixtures. It sounds like you have wire the fixtures directly to the power source where the switch does not control the light fixtures, so the power source will need to be wired through the light switch.

These units replace the ballast normally installed for the lamp(s) in. That makes me think the switch. This is a popular misconception.

The theory behind this misconception is that the power surge that occurs when you first power on a light will use as much electricity as five (or fifteen) minutes of the regular consumption of the bulb.

Wiring is explained to give basic instruction how current travels to the switch and back to the light. I show how to wire up this old Tfluorescent light fixture I got for free out of the trash. Lets see if I can make this old light to work again!

I am installing a fluorescent light fitting in my shed and want to install a one gang, one-way plastic light switch (with plastic back box). I have power coming into. Determine the length of the circuit cable that will run from the location of the switch to the location of the light fixture. Cut the cable accordingly and remove at least inches of the cable sheathing on both ends using a utility knife to reveal the colored wires. Run the cable from the switch to the fixture location.

For a fluorescent light , the best practice and a general rule will be to hook the live wire to the ballast. It is not compulsory as even if you connect the neutral wire to the ballast, the fluorescent light will still work. However, this is not advisable and not a standard practice in wiring a fluorescent light.

Doing it the standard way, make trouble shooting of the fluorescent light easier. The electrician installed a new wall switch in the kitchen, so that when I replace the fluorescent light , it can be turned on and off at the wall switch. Top Brand 58w Tubes in White Finish.

I am ready to install the new light. In the ceiling, there is a bare copper wire that I am assuming is the ground and will be wired to a screw on the light fixture. The cable between the switch and fixture (s) is also wire type, but must be run from either three way switch box to the fixture box that has the power source.

Do not deviate from the requirement.

Attach the black wire from the last fixture to the black wire from the power supply using an orange wire nut. Connect the white power supply wire to the white wire from the last fixture with another orange wire nut. Connect the bare copper wires from the power supply and the fixture in the same manner. Power source directly to fixture - When you want to add a switch to a light that is hot at the fixture , you can run a new wire cable from the fixture to a box containing the new switch.

The black caries the hot to the switch , the red carries the hot back to the fixture. Both will be hot when the switch is on. Loosen and remove the screws from the cover for the light switch that operates the light , using a screwdriver. Take off the cover, and note the color of the wire insulation for the wires that. Wiring fluorescent light fixtures is a common job for the do-it-yourselfer.

Due to their greener profile, the operating cost and improved quality, fluorescent lights are a popular choice for both homes and businesses. Whether you need to install a new light , or simply replace the ballast on a dead one, wiring a fluorescent light is a straightforward task, if you have the right tools and a. If you’re left with a wire that’s green, green and yellow, or bare copper, wrap it around the grounding screw on the fixture and tighten the screw before fastening the fixture to the mounting hardware and testing your new light. The live wire or phase is taken from the junction box to the switch board.

From another terminal of the switch , the wire is carried up to tube light set up and connected to port of the electronic ballast.