Immersion heater switch fuse

I was worried but realise now that the 15amp fuse or 16amp mcb is for the consumer unit and as you have just confirmed to me, the 13amp fuse is for the socket near the heater ! A fuse in consumer unit 2. A double pole switch ( no fuse ) with neon usually mounted in kitchen. Immersion heaters usually have a dedicated 16A supply from the fuse board. If you have one coming off the ring main then it should really be disconnected.

To replace the thermostat in the immersion heater should your water get scalding hot all of a sudden, make sure the electricity to the immersion is off and the fuse in the isolator switch is out. Undo the top screw’s of the thermostat cover and you will usually see a cable clamp holding the mains flex in place. Firstly if the fuse for the immersion heater blew when the old element faulted and it has not been replace then no electricity is getting to the new element to heat the water, so first thing really is to check the fuse at the consumer unit (fusebox) and if fitted the one at the immersion heater switch next to the cylinder.

WiFi enabled control for all manner of electrical applications connected to Timeguard’s FSTWiFi 13A Fused Spur Timeswitch. Ideal for switching lighting and electrical heaters with a Weathersafe IPversion FSTWIFITGV for outdoor uses. The immersion heater is 3kW. I pulled each cable and none seemed loose.

If the lettering on the cartridge fuse is not easy to. I have replaced the Fuse of the On peak Redring immersion heater and the current still trips out. The limescale in the water has built up on the immersion heater element over time and corroded it. The element has now blown, so the tank will need to be drained down and a new element fitted.

Shop today at TLC Electrical! My immersion heater blows the mains fuses when reaching temperature. I have changed the very old heater for an long life heater , but still no change.

Have replaced the mains supply cable, the cable from the switch to the thermostat, the switch and the thermostat. Mains (consumer unit) fuse is rated Amps and supplies only this and is whole. Item states Centeral heating spured off immersion heater switch. Now bearing in mind a boiler is not likely to pull more than an amp, is there really an issue here? Currently there is an old unfused switch near the tank (although in decent condition) used to switch the immersion on and off, there is another fused switch downstairs ( fuse currently removed!).

Even if so, presumably it would be better to replace this, but relative is keen to keep price down! It had a standard 2¼ immersion heater boss at the top and into that we have a short (12) 3kW immersion heater. Near the bottom we fitted another 2¼ immersion heater boss with another heater fitted horizontally. The best way to make sure the switch is off is to pull the fuse in the fuse box. You can pull the fuse with your fingers.

Insert the thermostat rod into the immersion tank and attach the probe wire and the thermostat wire with tiny retaining screws to the rod and base of the tank. If its on a simple amp plug as some are, then check the fuse first. Then there may be a switch or stat on the top of the heater element so you could check those. Improve Your Business ROI - Get A Better Deal On Fuse Switch. The top switch is called a fused connection unit and is most likely the supply to immersion heater , the next is a simple switch and I have really no idea what it might be for, the next box is likely the connection to central heating and the unit held to the tank is likely the sensor for the central heating so it knows when to heat the hot water.

Hi First of all - I know nothing about DIY! The system I have in my flat is a big black plastic water tank with. The fuse board tripped today when I turned on the immersion switch. Just wondering if I use the oil to heat the water will it trip also. Suitable for use with up to 3kW immersion heaters.

Switches the following lighting loads: 750W incandescent or halogen. Find China Manufacturers Of Fuse Switch.