Accelerator cable sticking

Buy Online or Reserve and Pick Up! This is a how to video showing step by step instructions on fixing your stuck or sticking accelerator cable on your Mercury Villager or Nissan Quest. An accelerator cable , sometimes called throttle cable , is a metal braided cable that serves as a mechanical link between the gas pedal and the engine’s throttle plate.

When the gas pedal is presse the cable is pulled and opens the throttle. As the throttle is what controls the power of the vehicle, any problems with the cable can quickly translate into problems with the drivability of the. Not enough slack in the throttle cable at hot idle?

Intermittent air leak on the vacuum side? I slowed right down using the gears then pulled onto the hard shoulder where I took the car out of gear and stopped the car whilst instantly turning the key to stop the engine (otherwise the engine would just rev right up). Unfortunately due to my bad Spanish the use of the. My SV6throttle was not snapping closed like it should do, a fairly simple job to oil the cable without any fancy tools.

Now it springs back quicker than a bikers grin on a sunny day! Sticking accelerator The video on the right contains advice from the USA after a number of Toyota cars were recalled because of sticking gas pedals. Your vehicle’s throttle control cable is a fairly basic design playing an important role in the control and operation of your car’s engine.

Clio accelerator sticking. More than likely a sticky cable.

High quality at low price. Note: The accelerator cable connects the carburetor ( throttle lever) with the accelerator pedal. The routing of the cable from the accelerator pedal rearward is as follows - From its attachment to the accelerator pedal in the cabin, the cable passes rearward through a metal tube in the floor pan. I have since resolved the stuck throttle problem.

The problem is not necessarily the fault of the ML. I had this on my Mazda petrol as well, I changed the throttle cable to no effect, and so took it to the local garage who cleaned the throttle body out FOC. As title said my accelerator is sticking , it is just at the start of travel I also have the same problem with my EI have used spray grease ( lots of it ) on the joint on the floor, top of peddle and at the top on the bulkhead with the spring on it.

Could be a few reasons but the most common is a mat or carpet blocking the travel of the pedal or a frayed cable either at the pedal end or the throttle body on the. Hello all, Got an annoying problem on my 1. My gas peddle is sticking. Is there an easy way to lube it? The cable will stick , meaning that the pressure needed to.

If your accelerator is sticking , it can be repaired by taking these steps. Recently, the throttle seems to be sticking. Right, probably was caused by the cable then if the garage has lubricated it and its OK now, however as you say, a throttle sticking on is dangerous and.

A sticking gas pedal can be the result of damage to the throttle cable , gas pedal assembly, or even the throttle body or carburetor. Make a few visual checks to. Have a look up under the footwell where the cable goes through into the engine compartment - sometimes a little grease just there stops the sticking.

Check the bar end weight.

If you push it on too hard and then tighten the allen screw it can put a lot of friction on the end of the grip and stop it returning. Replace the accelerator cable since it is worn and sticking. Throttle cable is perfect and I would have still had the sticking if I changed it. When installing the new one, I use a liquid graphite suspension called Lock-Ease, Graphited Lock. You could try lubricating it.

Drivers use these two cables , the front cable and the idle-hand throttle cable , to accelerate the bike, just like a pedal is used to accelerate a car. Because these cables are so important to a motorcycle’s function, it’s important to know how to adjust and fix them when they stick. Lawnmower throttle cables can get stuck because of rust and grit, making it difficult to control the mower. The accelerator pedal that operates the accelerator cable is located on the right side of the steering column.

Removing the Accelerator Cable Raise the hood of your GMC vehicle and prop it open. When replacing throttle cables i usually find the bushing or ferrule through the firewall has a groove in it from the old cable so the cure is to driill it out slightly the next size up so the cable can slide freely, also check the the hole in the end of the accelerator pedal lines up with the hole in the firewall. What Might Cause a Gas Pedal to Become Stuck ?